KEITHLEY 196 MANUAL PDF

KEITHLEY 196 MANUAL PDF

Visit us on the web at for more information: • Price Quotations • Drivers· Technical Specifications. Manuals and Documentation . Model System DMM Instruction Manual Rev. D. Manual Type: Primary User; Part Number: D. Release Date: Sep 17 View and Download Keithley DMM instruction manual online. 5 function autoranging digital multimeter. DMM Measuring Instruments pdf manual.

Author: Malabar Gardakus
Country: Burundi
Language: English (Spanish)
Genre: Marketing
Published (Last): 16 August 2004
Pages: 92
PDF File Size: 6.46 Mb
ePub File Size: 12.92 Mb
ISBN: 312-7-62698-234-7
Downloads: 45619
Price: Free* [*Free Regsitration Required]
Uploader: Moogunos

A good diode will typically measure between to IkO. Version B10 Binary Motorola S. If the self-test is successful, the J byte in the UO status word will be set to 1.

Take the reading from the display. Device-dependent commands can be sent either one at a time, or in groups of several commands within a single keitgley. HP Programining Example-Type in the following statements to place the instrument in the correct trigger mode for purposes of this demonstration: If an altered resolution is desired, use the manual Range buttons to display the resolution.

Keithley 196 System Digital Multimeter

While most keirhley today systems are using little endian for storing data, old Motorola CPU used in lot of Keithley instruments using big endian, so before you flash your ROM s, make sure endian is correct. December 4, at 7: To check or change the filter value of another function, select the function and repeat steps 2 through 5.

  KOSTAL CONNECTOR PDF

However, each device on the bus must have a unique primary address– a factor that should be kept in mind when setting the primary address of the Model This is the center frequency.

Diode Test— The 3kQ range can be used to test diodes as follows: NOTE The verification limits in this section do not include test equipment tolerance.

Report any damage to the shipping agent. The current zero value will then be displayed.

The cur- rent status of the MX-f-B program will be displayed. Bit 0 Reading Overflow — Set when an overrange input is keihley to the instrument. The value command may take on either of the following forms: The Model can switch up to 20 2-pole channels 20 single- pole channels with special cards such as the low-current card. Resolution can be remembered after power-down by run- ning Program 30 Save. The LI command is used to save the current instrument conditions.

When sending a wild card Translator word over the bus, there must be a space between the Translator word and the option number. If the line frequency setting is changed but not saved: HP Programming Example— With Translator words already defined, enter he following program statements to list them: Sudden shifts in reading. Enter the number 31 by pressing the ” 3 ” and ” 1 ” but- tons. Cal Locked Error A cal locked error occurs when trying to calibrate the in- strument over the bus with the front panel calibration switch in the disable position.

  ALCHEMIKAS PAULO COELHO PDF

196 System DMM Instruction Manual | Keithley

If there are no Translator words in memory, nothing will be displayed when the list is requested. As an example of deter- mining e. Do not use this application to check amplifiers that exceed the bandwidth of the Model This feature can be used for both 2-terminal and 4-terminal resistor measmrements up to 30kfl. Place the Model in “one-shot on external trigger” T7 as explained in paragraph 3. The instrument will then respond to the Translator words as well as Keithley device-dependent commands.

The instrument will power up in the V DC range.

Model forum thread Keithley document repro site xDevs. A Model specification LabView library example for K Keithley Photos Keithley The included files are annotated versions keithey the main non-power supply section of the Keithley Current Source.

Keithley System – In Stock, We Buy Sell Repair, Price Quote

In this example, note that only as many significant digits as necessary need be sent. Sending the Z2 manuak without a V value established is the same as sending the Z1 command.

Keithley Top PCB. The function may be programmed by sending one of the following commands: Increase the frequency input until the Model reads -S.

Previous post: