ZONE AMPLIFIER ZAA ZAA C AUTION AVIS 1 SAFETY INSTRUCTIONS 1 GENERAL USE (용도) 1 I NSTALLATIONS 2 F. Jedia JPAA/JPAA Amplifier Functions · JPAA Operating Instructions. Legislation and Compliance. RoHS Status: Not Applicable. Statement of. מגברי JDM היפרטרוניקס רכיבים וחלקי אלקטרוניקה מערכות כריזה והגברה מוצרי חשמל מגבר מיקסר חכם ל- 5 איזורי כריזה W. ZAA: A/A. ZAA: A/
|Published (Last):||3 April 2010|
|PDF File Size:||19.85 Mb|
|ePub File Size:||1.97 Mb|
|Price:||Free* [*Free Regsitration Required]|
Install equipment as follow conditions. Install at the place, not bending curved. Do not install this apparatus in a confined space such as a book case or similar unit. The apparatus shall not be exposed to dripping jm splashing and no object filled with liquids, such as vases, shall be place on the apparatus.
Locate this apparatus away from heat source, such as radiators or other device that produce heat. Do not drop objects or spill liquids into the inside of the apparatus. Keep in mind the following when connecting the apparatus.
Connect each connection of amplifier perfectly, if not, it maybe Caused hum, damage, electric shock in case of mis-connecting.
To prevent electric shock, do not open top cover. Connect the power cord with safety after check of AC power. This apparatus should be serviced by qualified service person.
It is best suited for call and message transmission installation with alert systems, music in industrial enterprises, offices, congregation halls and sport centers, schools, churches, hospitals, super-maket, and other similar occasions. Please pay close attention to the cooling requirements. Never block the air ndm in the sides and front of the amplifier the following is jdj of air-flow. Check inside temperature of rack system so as not to be more than 40 C for the stable operating in any case, we recommend you to install cooling fan additionally on the rear panel of rack cabinet.
Be sure rear of amplifier is securely mounted to rack.
T remote PTT level. Secound, you can increase input volume to the position “0” of LED indicator. Second, you can increase input volume to the position “0” of LED indicator. This is for pre signal or alert signal. T MIC remote control.
Operation voltage for mic priority is DC 24V to the screw terminal. For phantom, please push phantom switch to supply with P.
Cable for audio line should be used by shield cable. Users can extend cable at 30m MAX. You had better use proper input ilevel.
If clip indicator of output meter is turn-on, please turn GAIN control to the clock-otherwise for the optimum internal operstion. Turn gain volume and jrm controls of front panel to the clock-otherwise completely when you use phantom power. If not, speaker may get harmful due to loud noise power by power shock. ZAA, A havel been designed to use P. The stereo signal of the connected sound sources gets internally converted into a manual signal.
מגבר מיקסר חכם ל- 5 איזורי כריזה 240W
All signals can be recorded but recording out can not be adjusted by master volume because recording output is in the front of circuit of master volume control. Out put impedance should be ohms more for pre-amp operation. If all call switch, P. Maximum power output per zone speaker. For the direct output, use spk zone 4 and set speaker ATT.
You can hear telephone ring Via speaker from other office in the night. Third, contact terminal to what you want.
The battery connection cord has to be 3. All signal output of remote controller RC will be closed under setting “on” of priority switch on the rear of P. Remote controller RC is prior to any other prioroty priority is activated, an signals are closed But, P.
T MIC signal can be activated is spite of priority. The following is priority ranking against all signal inputs of system and priority signal is “NO” “OFF” automatically. Announcement only for M6 alertvoice message P. When not using microphoneturn microphone “off”.
This is to prevent is to prevent mistake from remote controller RC In case data are supplied to amplifier, send LED indicator lights. Busy means under operating of “TALK” or digital message. Pressing one of the zone button 1 to 5 delegates the signal to the desired loud speaker zone. Then, attenuation function in the main amplifier are reset and zone power-out is converted to HI impedance power output. The corresponding LED indicator lights. This makes you replay, stop recorded message of the memory bank M1-M6 one time without setting repeat function.
Amplifier P.A. 5 zone JDM ZAA
This function is same as that of “TALK” or “message” operation. This is RJ45 connector for power supply of audio, data, make sure that 4pairs LAN cable is necessary for optimum operation. Use LAN cable within m distance. It’s a community-based project which helps to repair anything.