HREAP DESIGN AND DEPLOYMENT GUIDE PDF

HREAP DESIGN AND DEPLOYMENT GUIDE PDF

H-REAP Design and Deployment Guide – Cisco Learning Read more about controller, lwapp, configuration, wireless, configured and wlans. HReap Design and Deployment Guide: /products_tech_noteashtml Configuring Hybrid REAP. 27, 24, , 2/8/, Wireless LAN IPv6 Client Deployment Guide New! 55, 14, , 6/29/, H-Reap Design and Deployment Guide.

Author: Dilabar Mijora
Country: Brazil
Language: English (Spanish)
Genre: Automotive
Published (Last): 21 March 2012
Pages: 274
PDF File Size: 4.84 Mb
ePub File Size: 11.41 Mb
ISBN: 864-2-42201-775-8
Downloads: 17009
Price: Free* [*Free Regsitration Required]
Uploader: Shataxe

So fail-over is not seamless.

I must admit though, I prefer your summaries to the matrix and release notes. Searching high and low for this but could not still get my hands on one. Hi Andrew Thank you for useful info and I really enjoy reading it.

Steve Williams June 27, at 7: The AP expects a response from the controller within 2 seconds, otherwise it sends up to 5 more hearbeat packets at 1 sec. BJ December 24, at 2: Here is a link from cisco.

We’re about to roll out wi-fi throughout our campus including remote sites and would like to use central authentication with local switching. We have tried to do load sharing by dividing deploymemt to both controller. Andrew vonNagy June 13, at Why must the latency not exceed 2 seconds v. Anonymous February 7, at Kristjan December 5, at guids This is still an open feature gap.

Anonymous March 16, at Andrew vonNagy December 13, at 6: I can be reached at cbagley nmmu. Anonymous August 24, at 7: Andrew vonNagy November 15, at 8: Anonymous July 2, at Aerohive has an advantage because they were able to develop their product without existing product roadmaps and feature sets to support and upgrade along the way.

But it’s still fairly manual. Additionally, feature limitations when using this mode of operation need to be clearly understood by network administrators prior to evaluating and deploying an H-REAP solution. Seems like a feployment approach.

  ALASTAIR FUAD-LUKE PDF

What is H-REAP mode?

Andrew vonNagy March 1, at 6: Because it should already know as it is configured this way before its primary WLC goes offline for some reason.

If you continue to run into troubles, you should call Cisco TAC to investigate.

KD July 2, at First, authentication timers on clients; they expect to have authentication complete within a reasonable amount of time, and if not then they will assume it has failed and try to reconnect and start the authentication process over.

I think we’ll see some big announcements from those two in 1H Anonymous November 16, desihn 9: Curious about your thoughts on the controller-less solution from Aerohive? Administrators should design a solution around these requirements as best as possible.

And we are noticing the loop in to the network? Would you able to advise me,by having APs in one group, what effects it would have on network? In this post, I will build on those basic fundamentals and provide more depth on the recommended deployment guidelines if you’re thinking about deploying H-REAP for remote sites.

Revolution Wi-Fi: H-REAP Deployment Guidelines and Feature Limitations

Xirrus does something similar, with a controller in every AP and coordination among multiple APs. Anonymous June 24, at 2: Andrew vonNagy June 29, at 8: The WAN latency can affect the responsiveness of the heartbeat communications and can cause the AP to disconnect from the controller and go into standalone mode. Local controller at remote site is primary controller for the APs at remote site and centrally located controller is secondary controller for the APs at remote site.

  FORSCOM SOLDIER RISK ASSESSMENT TOOL PDF

If you have code version 7. That way it’s easier to remain on top of the changes in an incremental fashion, rather than trying to figure out what changed from a year ago and three releases ago: In addition to feature limitations that apply to all H-REAP operational states, the following limitations also apply when the AP goes into standalone mode after losing connection to the controller. Ensure the secondary WLC is in the same mobility group, and ideally configured on each AP in the controller preferences.

What is H-REAP mode?

Andrew vonNagy November 17, at It is easy to add them to the group on their currently connected controller, just select each AP from the drop-down list within the H-REAP Group to add them. Anonymous December 13, at Posted by Andrew von Nagy at 9: In case of fail over if they go from group of one controller to default group of other, what will be impact? When we initiate fail-over from primary controller local to secondary controller central with ms or more WAN latency AP fail-over works fine however when AP gets associated to central controller the clients connected to the AP gets disconnectes and re-authetication takes place.

Hi Andrew, Great post with an awesome summary!

Kristjan, No configuration is replicated between controllers. Andrew vonNagy February 7, at 9: Newer Post Older Post Home. Troy Martin June 10, at 5: