and wiring for Japanese specification FX1N PLC main units. This manual covers basic hardware details for the FX1N Series Programmable Logic Controller. FX1N Hardware Manual – 三菱可编程控制器FX1N型PLC硬件手册. User’s Manual. (Data Communication). FX1S/FX1N/FX2N(C)/FX3U. Interface Modules. INDUSTRIAL AUTOMATION. MITSUBISHI ELECTRIC. MITSUBISHI.
|Published (Last):||10 September 2010|
|PDF File Size:||6.90 Mb|
|ePub File Size:||19.58 Mb|
|Price:||Free* [*Free Regsitration Required]|
Software warning 4 Indicates special care must be taken when using this element of software. All maintenance should be carried out in accordance with established safety practices. D, D M Program circuit error ref.
Please note that the over current induced by in-rush greatly reduces the relay contacts service life. LED is lit B Check mmanual programming error. Do not use this terminal Fuse Surge absorbing Diode. AC, World spec, CE registered. Mechanical interlocks MUST be fitted to all safety critical circuits. When the products associated with this manual are used as a system or individually, they must be installed in a suitable enclosure.
Owing to the very great variety in possible application of this equipment, you must satisfy yourself as to its suitability for your specific application.
If a high speed response is required, a current of 10 – mA must be used. See equation 1 for Rb calculation.
D Top cover for board. Terminals screws should be tightened to between 0. During this testing stage take extreme care not to touch hardwsre live or hazardous parts. The FX1N does not have battery backup, jardware a system requires backup of more than 10 days, a peripheral backup power source must be provided.
E C A Special function or optional equipment board. Grounding is recommended but if a proper ground cannot be provided, the PLC will still operate correctly without being grounded. Circuit protector or fuse? Note that the ground cable must not be connected to the same ground as the power circuits.
Terminal layouts The following selection of terminal layouts are taken from the FX1N product range. The capacitor backed memory will retain programs for a maximum hardare 10 days, and requires 30 minutes to recharge upon power up. Do not run input signals in the same multicore cable as output signals or allow them to share the same wire.
Mitsubishi Electric will accept no responsibility for actual use of the product based on these illustrative examples. If resistance Rp is less than the stated value, then add Hwrdware.
Mitsubishi FX1NMT-ESS/UL Manuals
Fix board to base unit using screws C. Remove the base unit top cover. These engineers should also be trained in the use and maintenance of the completed product. If a response time of 0.
Check the output LEDs for operation.
Mitsubishi FX1NMT-DSS Manuals
Do not remove this screw. Circuit protector or Fuse? AC Wor ld spec. Screw terminals must be hatdware to prevent a loose connection from causing a malfunction. C M3 screw to secure board.
Mitsubishi FX1N-24MT-DSS Manuals
The following instructions are also not suitable. This includes being completely familiar with all associated documentation for the said product. Secure top cover with M3 screw E. The enclosure should be selected and installed in accordance to the local and national standards. The operators should also be familiar with documentation which is connected with the actual operation of the completed equipment. See equation 2 for Rb calculation. FX0N series extension units do not have CE hsrdware.
Always ensure that mounted janual and blocks are kept as far as possible from high-voltage cables, high-voltage equipment and power equipment.
For greater detail, specifications and wiring examples for each optional unit, please see the relevant product manuals. Check the power LED is lit.
Each of the symbols used will now be listed with a brief description of its meaning. If in doubt at any stage of the installation of an FX1N Series Programmable Controller always consult a professional electrical engineer who is qualified and trained to the local and national standards which apply to the installation site.
Under no circumstances will Mitsubishi Electric be liable or responsible for any consequential damage that may arise as a result of the installation or use of this equipment. Never mount them to the floor or ceiling of an enclosure. FX0N series extension units do not have UL certification.