This tutorial is intended to give basic instruction on how to setup and run a Note: FloXpress will not work if the Flow Simulation add-in is currently installed. Solidworks FloXpress is a feature inside Solidworks that allows a designer simulate flow of fluids through a model. Based on the results of the. This simple tutorial is designed to show you the process of solidworks floxpress. The part that we use here is a simple part because our main goal is the process.
|Published (Last):||8 May 2009|
|PDF File Size:||20.60 Mb|
|ePub File Size:||16.43 Mb|
|Price:||Free* [*Free Regsitration Required]|
Home solidworks tutorial ebooks solidworks flowxpress In the fluids windowselect water and click next. I did it too, now or part is a closed chamber.
Tutorial – Using FloXpress in Solidworks? | GrabCAD Questions
Now there is a lid on one side. First you must model the following part and I assume that you know the basics of solidworks 3d modeling. SWA home about contact us. Trajectories are tutoorial to the flow velocity at every point. This is floxppress great tool to help you identify problem areas in your design and improve them before you manufacture any parts. The first step is to ensure that the model has no openings fully closed with lids.
Contact us for more information and buying SolidWorks at support nccs.
SOLIDWORKS Free Xpress Utilities-Part 4-FloXpress
This simple tutorial is designed to show you the process of solidworks floxpress. Thtorial can also choose to generate a report from the FloXpress simulation by simply clicking on the generate report icon at the bottom of the results tab. You can examine the flow in much more complicated parts like valves too the process is the same. Now go for the floxpress on the tools menu again. For the sake of keeping this tutorial short I leave it to you. All of these articles will be stored in the category of Daily Dose….
Based on the results of the simulation the designer. Define a plane parallel to the end face of the part and set the mm tuhorial distance.
The next step is to solve the model. You cannot use different fluids simultaneously.
Tutorial – Using FloXpress in Solidworks?
June 17, by Chris Taylor. Next we define the inlet boundary conditions. From the results window you can simulate the trajectory of fluid particles as they move through the model. In order to see the lids and getting a better sight of flow later on, we need to transparent the part. The boundary conditions are also clearly described in the report.
The opening must be closed with lids. A new assembly opens, the begin assembly window appears with your part ready to insert, just click on the working area and your part will insert there.
Once the geometry is valid, you next select water tuorial air as the fluid for the calculation. The part that we use here is a simple part because our main goal is the process of floxpress. So right click on main part and select appearance. Next we choose the fluid that would flow through the model. As you can see in the message box, the model is not ready for flow analysis.
I went with a C-D Nozzle geometry for this demonstration. Do the same for the other side and we will be ready for floxpress. We are here to close the two ends of the part so insert a new part just like cloxpress.
This simulations can be done using either pipes or bubbles. Once tloxpress have created the lids we can then proceed to begin the simulation. We then define the outlet conditions in terms of atmospheric pressure. A Microsoft Word report can be generated.
From the report we can obtain properties such as maximum flow velocity. The Solidworks FloXpress icon is located under the evaluate tab. The FloXpress wizard has a procedural sequence that enables the user maneuver through the simulation with ease and comprehensively understand the simulation.
A sample report is like the one shown below. This free tool allows you to calculate how fluid or air flows through a part or assembly document. Click on the next button again. Click next and then click solve and wait. Share this with your friends.
Home Support Daily Dose Now the part is ready. Now the part1 is added to design tree. Right click on it and select edit part:. Use this information in conjunction with experimental data and practical experience. The check geometry window appears which indicates the smallest passage.
The inlet conditions can be defined in terms of pressure, volume flow rate or mass flow rate.