View and Download ENSONIQ DP/4 musician’s manual online. DP/4 Music Pedal pdf manual download. Hello,. Welcome to , Inc. your online resource for technical documents and service information. This PDF package may contain information, . I bought a DP/4 but need a manual. There’s a Yahoo DP4 Group (dp4: Ensoniq DP4) with all the Manuals and more for DP4/+ as pdfs.

Author: Faegar Kizil
Country: Ethiopia
Language: English (Spanish)
Genre: Love
Published (Last): 13 October 2009
Pages: 208
PDF File Size: 9.20 Mb
ePub File Size: 13.16 Mb
ISBN: 332-7-52107-294-5
Downloads: 76671
Price: Free* [*Free Regsitration Required]
Uploader: Meztijas

This means it will be very difficult to remove this cormector by just pulling. The LCD display shows the error counts: Litiumbatteri – Eksplosionsfare ved fejlagtig handtering. Press on the base right where the silver slip is.

Turn the unit up side down. Existing presets which were set in the range of 6 to 10msec did nesoniq and will not now sound coaect. Note where the silver clip is attached to the top and bottom front rails.

Test the unit see nesoniq. To put flat head screw and KBPS nut on right side transformer side you will need to hold the nut with long needlenose pliers while you screw the screw in. This clip holds the front panel assembly together.

Make sure that you order the same version that is currently in the unit. Move the lid down into place. The display shows janual Test: Paristo voi rajahtSa, jos se on virheellisesu asennettu.

Rather than diagnose and exchange individual components, you will replace complete modules.

Other Media Files : Ensoniq DP4+

Com Technical Document Distribution Eneoniq Sometimes the unit in question can wake up in a state of mild confusion and this message might appear. Reinstall the transformer secondary board screws and star washer on the ground pad. The sound of existing presets is not affected and the displayed values will now be coaect.


Remove the eight 8 screws from the lid. The switch can be set to “Enabled” if the user experiences any download problems or desires the extra level of checking.

Figure 1 for location. Carefully connect the cable and wires, see Figure 4 for connections. See Figures 3 and 4 for more information and AC power connections.

Ensoniq Corporation – DP/4 – Reference Manual

Large original over-sized drawings will need to be taped together. Also please stay online while printing this document to make sure you get all the pages.

This document was assembled from a variety of sources and is the result of our many years in the music repair business. These cables may be present in studios that own some equipment with balanced inputs and outputs. Connect the scope probe to ground.

ENSONIQ DP/4 Musician’s Manual

The LCD display momentarily shows: Check all the fuses enzoniq make sure they are not blown. Full text of ” Ensoniq: We have found that some units develop further problems once a module has been changed. Attach the green transformer wire to the top lug of the switch.

Figure 2 – What Plugs to Use 4. An error message will be displayed instead of the confirmation message if there was a problem with the incoming data. This may be a result of dp handling of cables, especially the pin and pin ribbon cables between the keypad board and the main board. TRS cables also should have braided wire surrounding the other three wires to shield against interference. To Stop the Bum-in Test: Insert the replacement transformer secondary board.


However, the 80 ROM presets are automatically d;4 back into the internal memory after reinitializing. Connect the pin and ensohiq cables to the main board.

Power up, test the unit. Connect Output 2 to Input 2 c. Vaihda paristo ainoastaan laitevalmistajan suosittelemaan tyyppin. Be sure to reinitialize the system see p. If the above methods do not return the system to normal operation then there is a problem in one of the modules.

Documents, presets, manuals Ensoniq DP4+ – Audiofanzine

If the memory does get scrambled, it will be necessary to reinitialize the system. This change affects the documentation in that the parameter limits are now actually 1msec to lOsec instead of 50 isec to lOsec. Make sure the Receive enable is set to “On” and the ID number is set correctly.

We just wanted to let you know that we are using a high retention force connector on the transformer.

To see channel 2, press B. Slide board to left front panel closest to you to clear the main board heat sink on the right side of the main board.

Disconnect all cables from the Main Board: Both displays go blank and all LEDs turn off. The nuts will drop inside the unit, be sure to retrieve them. Watch out for them, and please don’t pull on the wires!