Small Spot/Mark (Separate Amplifier) Extremely thin beam ideal for detection of minute objects and marks. Order Omron Automation and Safety E3C-VS1G (ZND) at DigiKey. Check stock and pricing, view product specifications, and order online. Omron E3C-VS1G Photoelectric Sensor 10mm for E3C Amplifier: : Industrial & Scientific.

Author: Fell Nizuru
Country: Nicaragua
Language: English (Spanish)
Genre: Travel
Published (Last): 18 February 2014
Pages: 325
PDF File Size: 6.49 Mb
ePub File Size: 1.69 Mb
ISBN: 348-4-73234-858-1
Downloads: 45271
Price: Free* [*Free Regsitration Required]
Uploader: Zululmaran

Mutual Interference Prevention Polarizing Filter: M8 and M12 Connectors? Use the following methods to attach and remove Fiber Units. This catalog is protected by copyright and is intended solely for use in conjunction with the product. Do not use thinner or other organic solvents.

For bending-resistant cable, see Attachment to Moving Parts on page C Doing so may cause explosion or burning.

Insert a capacitor, etc. Strong, conductive electrical wire 2 x 0.

Cable Tensile Strength When wiring the cable, do not subject the cable to a tension greater than that indicated in the following table. The following are some examples of applications for which particular attention must be given. Systems, machines, and equipment that could present a risk to life or property. If not grounded, switching noise in the power supply may cause malfunction. Cable diameter Less than 4 mm 4 mm or greater Tensile strength 30 N max.

Separate Sensors to distance where interference does not occur. For this type of application, separate the Sensors by at least 1.

Nuclear energy control systems, combustion systems, railroad systems, aviation systems, medical equipment, amusement machines, vehicles, safety equipment, and installations subject to separate industry or government regulations. Doing so may result in damage from burning and fire, particularly if the liquid is flammable. However, if the workpieces are close to the Photoelectric Ommron, light ommron the adjacent Emitter may be received and cause the Sensor to change to the incident light state.


This may weaken performance. Typical measures are as given in the following table. For the E3S-C, the optical axis and the mechanical axis are the same, so the omrno axis can be easily adjusted by aligning the mechanical axis. Hold the connector cover to connect or disconnect the connector.

The Reflector cannot be mounted if there is any oil or dirt remaining. Typical e3c-cs1g include the minimum sensing object, engineering data, step height detection data, and selection list for specifications. This is not intended to be an exhaustive list of all possible uses of the products, nor is it intended to imply that the uses listed may be suitable for the products: Otherwise, it may malfunction or fail.

Omron E3CVS1G Photoelectric Sensor, 10 mm Reflective, NPN Output Buy from Cross

Outdoor use, uses involving potential chemical contamination e3c-vs1t electrical interference, or conditions or uses not described in this catalog. If the Sensor and the load e3c-vs1 connected to separate power supplies, turn ON the Sensor power before turning ON the load power. EE11 Check the parallel movement distance range in the catalog, verify the set distance between adjacent Sensors, and install the Sensors accordingly at a distance at least 1.


Close mounting of Sensors is possible ec-vs1g alternating the Emitters with the Receivers in a zigzag fashion up to two Sensors. The following measures can be taken to avoid mutual interference. Through-beam Sensors Reflective Sensors 1 If Sensors are mounted in close proximity, use Sensors with the interference prevention function. The axis perpendicular to the center of the lens.

Omron E3c-vs1g E3CVS1G Photoelectric Sensor Switch

This is because the Sensors may affect each other and cause output chattering even if separated by more than the Sensor sensing distance. Type of noise Noise intrusion path and countermeasure Before countermeasure Noise enters from the noise source through the frame metal.

Do not subject a shielded cable or coaxial cable to tension. Power Supply Types An unsmoothed full-wave or half-wave rectifying power supply cannot be used. The lens, case, and fiber covering are made of plastic, so this setup cannot be used if there is a possibility of contact with solvents that will corrode or degrade e.

Optical energy does not act as an ignition source, thus there is no danger e3c-cs1g explosion or fire. Placing them in the same conduit or duct may cause damage or malfunction due to induction interference.

Next post: