CCNP SWITCH 6.0 INSTRUCTOR LAB MANUAL PDF

CCNP SWITCH 6.0 INSTRUCTOR LAB MANUAL PDF

CCNP SWITCH 6 – BitRadius. Instructor Lab Manual Book everyone. Download file Free Book PDF Ccnp Switch Instructor Lab Manual at. CCNP: Implementing Secure Converged Wide-area Networks v – Lab Copyright © Ensure that the switch is set up so that both the router and host are in the same. VLAN. .. Figure Internet Explorer Security Alert Prompt. ccnp switch instructor lab pdf. CCNP SWITCH Instructor Lab Manual. This document is exclusive property of Cisco Systems, Inc.

Author: Douzilkree Tygogore
Country: Lithuania
Language: English (Spanish)
Genre: Travel
Published (Last): 15 May 2011
Pages: 60
PDF File Size: 12.8 Mb
ePub File Size: 10.12 Mb
ISBN: 114-3-51053-564-3
Downloads: 53608
Price: Free* [*Free Regsitration Required]
Uploader: Gakus

The switches are connected via an DLS1 config ip dhcp excluded-address To maintain an efficient STP topology, the root bridge must remain predictable. Add VLAN 10 and 20 to all of them. The ALS2 output is similar. You must apply identical configurations on each switch for MST to work properly.

CCNP SWITCH Lab Manual, 2nd Edition

Switch erase startup-config Erasing the nvram filesystem will remove all configuration files! Complete the following table with the appropriate verification methods and mitigation approaches for the attack types specified in the left column.

The following is a sample configuration for the trunks and EtherChannel from DLS1 to the other three switches. Background The current network equipment includes a distribution cccnp switch and two access cfnp switches.

Authentication is configured by defining a list of methods for authentication and applying that list to specific interfaces.

There are redundant uplinks nanual the access layer and distribution layer. The instance number can be between 0 and Permission is granted to print and copy this document for non-commercial distribution and exclusive use by instructors in the CCNP.

  CABLECOM BESCHWERDEBRIEF PDF

In the previous steps, you configured EtherChannels as Layer 2 trunk connections between switches. Observe the LEDs on the switch to check the status of the link. Verify your configuration using instrucror show udld interface-id command.

Use the show spanning-tree vlan 1 command on ALS2 inztructor look for a root port. Cable the equipment as shown. The default VTP mode for the and switches is server mode. Other switches such as a or aand Cisco IOS Software versions can be used if they have comparable capabilities and features. The work is protected by local and international copyright laws and is provided solely for the use of instructors in teaching their courses and assessing student learning.

Notice what happens when the port is brought up. Information obtained through CDP is used to determine when an IP phone is attached to the access port. In this lab, you will observe what spanning tree does and why. Issue the show spanning-tree command on one of the switches.

Cisco Networking Academy, CCNP SWITCH Lab Manual, 2nd Edition | Pearson

The standby command configures the IP address of the virtual gateway, sets the priority for each VLAN, and configures the router for preempt. Click here to sign up. Verify that you have Layer 3 connectivity by attempting to ping the other side of the link.

Configure DLS1 to exclude the first addresses from each subnet from DHCP to avoid conflicts with static IP addresses using the ip dhcp excluded-address low-address [high-address] global configuration command. Management traffic usually includes traffic for managing the switches, including VTP frames. Manaul the question mark when you type the global configuration command spanning-tree vlan?.

  BF964 DATASHEET PDF

Issue the show vlan brief command to view the VLAN configurations. However, VTP does not work unless trunk links are established. DLS1 show etherchannel summary Flags: This is useful when dealing with LWAPs, which usually do not have an initial configuration.

By default, spanning tree runs on every port. CDP works over access links as well. The access layer switches depicted in the topology are assumed to support PoE for the IP phones.

ccnp-switch-instructor-lab-manual-slm

ccnp Configure an interface to communicate with the access points. Creating the Lab Files. This lets you have workgroups within an organization while keeping them isolated from each other. Was the ping successful? Issue the show vlan command from privileged mode on both access layer switches. Configure VLANs and switch access ports. Notice that all the ports have identical spanning tree behavior for each VLAN.

The output should be similar to manuap following. These are known as SVIs. After configuring all four switches with this command, use the show spanning-tree command to verify the configuration: The CCNP certification requires candidates to pass three 1.