BOVERKETS KONSTRUKTIONSREGLER PDF

BOVERKETS KONSTRUKTIONSREGLER PDF

(Swedish)Independent thesis Basic level (university diploma), 15 credits / 22,5 HE creditsStudent thesis. Regelsamlingen för byggande innehåller Boverkets byggregler, BBR, med • Regelsamling för konstruktion – Boverkets konstruktionsregler, BKR, . Building permit. On most occasions, you need a building permit if you wish to build a new house, build an addition to your house or if you want.

Author: Mekasa Tusho
Country: Benin
Language: English (Spanish)
Genre: Health and Food
Published (Last): 13 July 2018
Pages: 335
PDF File Size: 13.18 Mb
ePub File Size: 6.50 Mb
ISBN: 143-7-31346-867-1
Downloads: 46861
Price: Free* [*Free Regsitration Required]
Uploader: Taulrajas

The biggest change to the rules for structural shear design is the requirement for minimum shear reinforcement in concrete beams. All measurements are calculated based on the following documents and conditions Sweden: The results of these calculations are presented in Table 3. It is assumed that the length and width of the building are twice as long as the height to the ridge of the roof.

The form factor is increased in shadow zones. The practical significance of this difference is very small; it only emerges in this thesis when the center distance between the shear reinforcements are determined in example tree. Eurocode 2 provides a clearer definition of how much deflection can be allowed, it was not supplied in Boverkets structural design rules.

Roof with thermal insulation. The tables of roof dimensions do not take wind load into account. The effect of wind load on bverkets roof and wall cladding is determined by the form factor and the characteristic value of wind pressure qk. If both the length and width of the building are twice as long as the height of the roof ridge, the fixing elements must be selected by taking into account the tensile load in proportion to the following form factor values.

Roof without konstruktionsreger insulation. The relationship between the snow load form factor and roof konstruktinosregler is presented below. The information presented is suitable for single and double pitched roofs.

  BASTA DE HISTORIAS ANDRES OPPENHEIMER DESCARGAR PDF

Form factor maximum values are specified below in roof schemes according to the roof slope. The distance is larger according to Eurocode compared to BKR. The results in Table 2.

Then find the value qk in the tables according to the type of terrain and the building height. If the wind blows from a certain type of terrain towards a different terrain, the wind load remains the same for the first two kilometers of the new type of terrain. Boverket publishes the Swedish building code. The snow load on the roof is defined by the characteristic value skwhich is calculated as the product of the snow load reference value s0 and the form factor m.

The regulations you need to know and follow depend on what you want to build or alter. Boverkets Konstruktionsregler BKR 94 design standards. Wind load pull — self-weight. The form factor m is used for calculating the dimensions of the cladding. The building code in Sweden contains mandatory konstruktionsrrgler and general recommendations.

The form factor m depends on wind direction and the form of the building as presented in the table below and on the next page. Taking into account the requirement of minimum konstruktionsregle, table 2. This reinforcement should be installed along the entire beam, whether it is needed to achieve sufficient strength or not.

These two methods are used to calculate how konstruktionsretler a beam deforms at different relative humidity. In order to demonstrate the differences in structural design, with respect to shear force, three examples are calculated.

Swedish Regulations for building works

You can also find general information about accessibility, dwelling design, obligatory ventilation control and about the Swedish regulatory hierarchy. Compared to table 2. The reason for the introduction of the Eurocode is to try and eliminate trade barriers between member states.

Each example is calculated in accordance with three different methods, two taken from BKR and one from Eurocode 2. Later, in conjunction with the technical consultation and start-up statement, the building committee shall deal with the technical property requirements regarding dwelling design and other technical property requirements.

  ANALYSE JACQUES DOUCHET PDF

The value qk is determined based on the reference wind speed vref, the type of terrain, and the height of the building.

Swedish Regulations for building works – Boverket – Boverket

The partial factors method is applied. Go to the page menu Go to boverkeys page content. When you build a building you need to follow the building code. Boverket Boverket drafts mandatory provisions and general recommendations in Boverket’s Building Regulations. The municipal building committee shall, among other things, assess whether the design requirements are fulfilled.

The value of the wind speed vref is selected based on the location of the building. This is explained by the differences in how the creep rate is determined in the different methods. Form factor m is used for selecting the fixing elements of roofing and determining their dimensions. This thesis aims to show what impact this change from Boverkets structural design rules BKR to the Eurocode will have on the dimensioning of shear reinforcement and the calculation of deformation in concrete beams.

To examine differences between the calculations of deformation, one method konstruktionrsegler BKR and one from Eurocode 2 is used.

The municipal building committee The municipal building committee shall, among other things, assess whether the design requirements are fulfilled.

The snow load reference value depends on the location of the building. The load reduction factor Y is found in the following table.

Login LT EN e.