ASTM G50 PDF

ASTM G50 PDF

We provide outdoor weathering and indoor corrosion testing, including outdoor exposure per ASTM G50 standard. were employed by referring to ASTM G50 standards. Eight locations were selected as the test sites: Peukan Bada, Ulee Lheu, Lingke, Lampulo, Suak Ribee. ASTM D, Section , to make an “X” scribe (Fig. 1). The scribe tool shall ASTM G50 Atmospheric Corrosion Testing, and others. A log will be.

Author: Mautaur Akinorisar
Country: Bangladesh
Language: English (Spanish)
Genre: Travel
Published (Last): 12 November 2016
Pages: 82
PDF File Size: 7.60 Mb
ePub File Size: 2.15 Mb
ISBN: 622-1-95632-805-3
Downloads: 74785
Price: Free* [*Free Regsitration Required]
Uploader: Shaktitaur

You are now logged in to your account. It is also good practice to retain samples of all materials exposed so that possible effects of long-term aging can be measured.

Also, as corrosivity may vary at a site from season to season, exposures should be made either at the same time of the year to minimize variability or these differences should be established by multiple exposures. Enter your asym account email address to request a password reset: We have no amendments or corrections for this standard. ASTM D Standard Practice for Evaluating the Relative Lightfastness and Weatherability of Printed Matter This standard describes procedures for the determination of the relative lightfastness and weatherability of printed matter under the following conditions, which involve exposure to natural daylight or accelerated procedures in the laboratory.

Standards Subsctiption may be the perfect solution. AAMA Voluntary Specification, Performance Requirements and Test Procedures for Superior Performing Organic Coatings on Aluminum Extrusions and Panels This specification describes test procedures and performance requirements for superior performing organic coatings applied to aluminum extrusions and panels for architectural products.

GM M Flexible Laminating Films and Film Plastic Laminates This specification details the requirements for flexible plastic films that may be laminated to either metal or plastic substrates. This specification covers the performance requirements of instrument panels, consoles, door trim, quarter trim panel, garnish moldings, armrests, headrests, assist handles, rear window trim panel and seat trims.

ASTM D Standard Practice for Xenon Arc Exposure Test with Enhanced Light and Water Exposure for Transportation Coatings This test procedure is used to simulate the physical and environmental stresses that a coating for exterior transportation applications for example, automotive is exposed to in a subtropical climate, such as southern Florida.

  DELL S2409W PDF

As the voice of the U. This specification establishes requirements and test methods for the materials, dimensions, warp, shrinkage, impact strength, expansion, appearance, and windload resistance of extruded single-wall siding manufactured from rigid unplasticized PVC compound.

ASTM E Standard Practice for Exposure of Cover Materials for Solar Collectors to Natural Weathering Under Conditions Simulating Operational Mode This practice provides a procedure for the exposure of cover materials for flat-plate solar collectors to the natural weather environment at temperatures that are elevated to approximate operating conditions.

Standard practice for conducting atmospheric corrosion tests on metals – CERN Document Server

Standards Subscriptions from ANSI provides a gg50, multi-user solution for accessing standards. Your Alert Profile lists the documents that will be monitored. ASTM D Standard Practice for Conducting Exterior Exposure Tests of Paints on Wood This practice covers procedures to be followed for direct exposure of house and trim paints on new, previously unpainted wood materials to the environment.

This specification covers polyolefin-based plastic lumber products for use as exterior residential decking boards. No items in cart.

ASTM G50 Outdoor Exposure Testing and Corrosion Analysis

The materials shall be classified into four types. You may delete a document from your Alert Profile at any time. Because of the variability and complexity of weather effects and the industrial and natural factors influencing the atmospheric corrosivity of a test site, a multi-year exposure period should be considered to minimize their influence. Also, as corrosivity may vary at a site from season to season, exposures should be made either at the same time of the year to minimize variability or these differences should be established by multiple exposures.

This specification describes test procedures and performance requirements for pigmented organic coatings applied to aluminum extrusions and panels. Link to Active This link will always route to the current Active version of the standard.

Print 1 2 3 4 5 page sstarting from page current page. ASTM C Standard Practice for Outdoor Weathering of Construction Seals and Sealants This practice describes outdoor exposure procedures used to determine the weathering durability of building construction, y50 and sealants. The control specimens should be from a material having established weathering characteristics.

  BERNA MORAN EDEBIYAT KURAMLAR PDF

ASTM G50 – 10(2015)

Polymers consist of homopolymer, copolymers, and elastomer compounded with or without the addition of impact modifiers ethylene-propylene rubber, polyisobutylene rubber, and butyl rubbercolorants, stabilizers, lubricants, or reinforcements. The control specimens should be from a material having established weathering characteristics. Today, some 12, ASTM standards are used around the world to improve product quality, enhance safety, facilitate market access and trade, and build consumer confidence.

A substantial amount of corrosion data shall have been astmm for the control specimens. A substantial amount of corrosion data shall have been accumulated for the control specimens.

To access documents, please register your equipment here. This specification describes procedures for conducting natural weathering exposure tests to evaluate the exposure tolerance of interior automotive materials, components, and assemblies.

Please login to your authorized staff account to use this feature. This practice covers and defines conditions for exposure of metals and alloys to the weather. It is presented as an aid in conducting atmospheric corrosion tests so that some of the pitfalls of such testing may be avoided.

Already have a user account? GM M Decorative Interior Plastic Laminates and Films This specification gives the durability requirements for plastic parts decorated with wood grains, or patterns for interior trim panels. Because of the variability and complexity of weather effects and the industrial and natural factors influencing the atmospheric corrosivity of a test site, a multi-year exposure period should be considered to minimize their influence.

This practice is intended to cover procedures for aztm exposure of plastic materials to weather. It is aatm as an aid in xstm atmospheric corrosion tests so that some of the pitfalls of such testing may be avoided. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.