ASTM D5587 PDF

ASTM D5587 PDF

Tear test of Fabric by trapezoid method to ASTM D ASTM D covers the measurement of the tearing strength of textile fabrics by the trapezoid tear test using a constant-rate-of-extension-type (CRE) tensile. ASTM D Tearing Strength of Fabric by. Trapezoid Procedure. • Scope – this test method describes the determination of the tearing strength of fabrics by the.

Author: Maujora Gardami
Country: Haiti
Language: English (Spanish)
Genre: Software
Published (Last): 23 November 2010
Pages: 60
PDF File Size: 7.40 Mb
ePub File Size: 15.77 Mb
ISBN: 346-2-43786-970-6
Downloads: 65117
Price: Free* [*Free Regsitration Required]
Uploader: Sami

Glossary of Materials Testing Terms. The components of variance for trapezoid tear strength expressed as standard deviations were calculated to be the values listed in Table 3. The values stated in inch-pound units may be approximate. Mark each ast with an isosceles trapezoid template see Figs. The nonparallel sides of the marked trapezoid are clamped in parallel jaws of a tensile testing machine.

ASTM D – tearing strength of fabrics by the trapezoid procedure

Discover simpler and smarter testing with features such as pre-loaded test methods, QuickTest in seconds, enhanced data exporting: Instructions are provided for testing specimens with or without wetting. For rolls of fabric, take a sample that will exclude fabric from the outer wrap of the roll or the inner wrap around the core of the roll of fabric.

It is recognized that some constant-rate-of-traversetype CRT tensile testing machines continue to be used. In the astj of ast an agreement, take the number of fabric rolls specied in Table 1. It is recognized that some constant-rate-of-traverse-type CRT tensile testing machines continue to be used. This precaution is most important when testing bowed fabrics. The highest peaks appear to reect the strength of the yarn components, individually or in combination, needed to stop a tear in fabrics of the same construction.

  KHARIZZMATIK EMANCIPATION PROCLAMATION PDF

If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below. It is useful for estimating the relative tear resistance of different fabrics or different directions in the same fabric.

Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.

ASTM D5587 Tearing Strength of Fabrics by Trapezoid Procedure

Within this limitation, this test method has no known bias. The values stated in inch-pound units may asttm approximate. The highest peaks appear to reflect the strength of the yarn components, individually or in combination, needed to stop a tear in fabrics of the same construction.

If a bias is found, either its cause must be found and corrected, or the purchaser and the supplier must agree to interpret future test results with consideration to the known bias. Hold the short edge taut, and let the remaining fabric lie in folds.

Tear Strength of Fabrics – Trapezoid Procedure

The separation of the jaws is increased continuously to apply a force to propagate the tear across the specimen. Instructions are provided for testing specimens with or without wetting. The minimum tearing force, however, is indicated to be above the lowest valleys. Ast 2—The tabulated values of the critical differences should be considered to be a general statement, particularly with respect to betweenlaboratory precision.

Description Literature Contact Us This standard mainly applies to most woven textile fabrics, but can be applicable to fabrics produced by other techniques. Label to maintain specimen d5587.

Lower shifts corresponding to yarn movement do not qualify as peaks since no yarns are broken. Ensure specimens are free of folds, creases, or wrinkles. We offer machines, apparatus, testers, tensile grips, test fixtures, clamps, holders, jigs, faces, jaws, extensometers, environmental and humidity chambers, furnaces, baths and custom solutions for unique applications. This test method allows the use of the CRT-type tensile machine when agreed upon between the purchaser and the supplier.

  BOBOK DOSTOEVSKY PDF

Signicance and Use 5.

The separation of the jaws is increased continuously to apply a force to propagate the tear across the specimen. As a minimum, the two parties should take a group of test specimens that are as homogeneous as xstm and that are from a lot of dd5587 of the type in question.

The American Society for Testing and Materials takes no position respecting the validity of any patent rights asserted in connection with any item mentioned in this standard. By continuing to use our site, you accept our cookie policy. The valleys recorded between the peaks have no specic signicance.

Consequently, these test instruments may be used when agreed upon between the purchaser and the supplier. Consequently, these test instruments may be used when agreed upon between the purchaser and the supplier. In any xstm, it is recommended that computer-processed data be veried against known property values and its software described in the report.

Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM Headquarters. The nonparallel sides of the marked trapezoid are clamped in parallel jaws of a tensile testing machine.

Bluehill Universal Brochure Bluehill Universal Software is built from the ground-up for touch interaction and an intuitive user experience.