A Datasheet – Vcbo = V, PNP Transistor – Panasonic, 2SA datasheet, A pdf, A pinout, A equivalent, data, A circuit. A Datasheet, A PDF, A Data sheet, A manual, A pdf, A, datenblatt, Electronics A, alldatasheet, free, datasheet, Datasheets, data sheet. 2SA transistor pinout, marking A Marking. Sometimes the “2S” prefix is not marked on the package – the 2SA transistor might be marked “A”.
|Published (Last):||17 April 2018|
|PDF File Size:||5.23 Mb|
|ePub File Size:||6.44 Mb|
|Price:||Free* [*Free Regsitration Required]|
Cold Working The alloy can be cold worked, but requires more force than the lower carbons steels in so doing. Are you a distributor who is interested in being listed here?
Machinability Machinability is relatively poor for alloy. Welding may be welded by all of the welding methods. See “Heat Treatment” and “Tempering”.
Acronal A is a straight datasheeet binder with good wet adhesion on difficult substrates. Forging Forging may be done at F down to F. We’re sorry, but the industry you have selected is not currently available in your chosen language. Before forging the steel should be given a full anneal at F and slow cool so as to homogenize the alloy prior to forging. Mean Coeff Thermal Expansion. It is intended for high hardness and strength, but also tends to be brittle.
Distributors will offer small quantity buys while mills will generally only sell large quantities, with delivery times anywhere from 10 to 50 weeks depending on size and form required This material is stocked primarily in Flat Rolled Products by 28 distributors but is also available to a lesser extent in Bar Products, and Wire Products.
For cutting tools it is common practice to harden only the cutting edge by induction heating and quenching so as to retain the toughness of the steel behind the hardened edge.
A Datasheet, PDF – Alldatasheet
Heat Treatment The steel may be hardened by heating to F and quenching in oil. Acronal A has applications in architectural finishes, wood paints, wood stains, latex paints, and textured finishes.
It is a APEO-free, excellent resistance to dirt pick-up, very good wet adhesion, and a broad formulation latitude. Tempering Temper at to F. The alloy can be cold worked, but requires more force than the lower carbons steels in so doing. Anneal at F and slow cool in the furnace. Forming may be accomplished by conventional methods. You may choose a language below to continue to this industry or close this dialog above.
Modulus of Elasticity Tension. However, UL assumes a864 responsibility or liability for the accuracy of the information contained on this website and strongly encourages that upon final product or material selection information is validated with the manufacturer. However is more difficult to form and requires greater force to do so than for the lower carbon steels. Forming Forming may be accomplished by conventional methods.
Hot Working Hot working may be done in the to F range. Annealing Anneal at F and slow cool in the furnace. This website provides links to other websites owned by third parties. The information presented here was acquired by UL from the producer of the product or material or original information provider.
The content of such third party sites is not within our control, and we cannot and datashset not take responsibility for the information or content. Hardening Hardens by cold work or heat treatment. Machinability is relatively poor for alloy. Hardens by cold work or heat treatment. Principal Design Features This is a high carbon alloy of the plain carbon steel family.
This is a high carbon alloy of the plain carbon steel family. Typically used for springs or cutting tools requiring sharp cutting edges such as grass or grain cutting tools. This should be followed by a dwtasheet heat treatment.
Applications Typically used for springs or cutting tools requiring sharp cutting edges such as grass or grain cutting tools.
The steel may be hardened by heating to F and quenching in oil. Forging may be done at F down to F. Modulus of Elasticity Torsion. It is important to pre-heat at to F and post-heat the weldment at to F. This steel is capable dqtasheet a Rockwell C 55 hardness at the lower tempering temperature. Hot working may be done in the to F range. Temper at to F.