EDSVSS−9. 9ä. System Manual. (Extension). 75 kW l. EVSxS EVSxS. Servo inverter. Global Drive. The System Manual is the basis for the description of the vector frequency inverter. Together with the System Manual (extension), document number. The vector range of frequency inverters is also perfectly equipped to handle complex applications, such as deployments in dosing, filling and feedforward.
|Published (Last):||28 December 2015|
|PDF File Size:||18.84 Mb|
|ePub File Size:||10.59 Mb|
|Price:||Free* [*Free Regsitration Required]|
9300 series servo inverters
Temperature inside the controller. Error “positive position limit”. Drive cannot follow the digital frequency I max limit.
Have a look at this document from Helmholtz, it gives an example on whatmust ,enze set and how to so the CAN modules can read and write to a drive:. Impermissible programming Check position program: Internal fault power stage.
Negative limit switch was reached.
Troubleshooting and fault elimination. You could probably recreate the Helmhotz drivers by yourself, if you knew how the CAN module communicates with the CPU over the backplane, how the CAN module must be parametrized for CAN BUS and how toexchange betweenthe CAN module and the drive,, If you do not have the information, I strongly suggest you get purchase the Helmholts CAN parametrization software and the handling blocks for the S, so you can concentrate on your project making the drives do what you need them to do instead of finding ways to talk to the drives.
Error “actual reference dimension offset”. Change the parameter set from absolute to relative. Sensor for detecting the heatsink temperature indicates undefined values.
Increase following error limit under C Parameter set mode is absolute instead of relative. Follow us on Twitter Youtube. Find out why the value was exceeded e. Control drive in negative direction. Perform one of the following functions and restart: Anything is possible, with enough ressourcesinformation and time. Find out why the value was not reached e.
servo inverters – Lenze in the Americas. As easy as that.
New question published by Shahjee is split to a separate thread with the subject brake functions or Brakes will Automatically applied. Heatsink temperature sensor error. The reference point is not known. Error of the program function “set position value”. Site Explorer Site Explorer. Hello aran; Anything is possible, with enough ressourcesinformation and time. Perform one of the following functions and restart:. Negative position limit C was not reached. Error “negative position limit”.
Complain wrong Brand ,enze Model non readable. Drive cannot follow the digital frequency I. Error “negative limit switch”. Start homing in the program. Temperature inside the controller Sensor for detecting the internal temperature indicates undefined values. Sensor for detecting the internal temperature indicates undefined values. Product Support Services Forum mySupport.
Handling blocks should be ordered from Helmholtz, look on page 96 of the document page 8 of In the case of absolute positioning, no homing was performed before the first positioning. Error “positive limit switch”. Have a look at this document from Helmholtz, it gives an example on whatmust be set and how to so the CAN modules can read and write to a drive: The angle difference between set and actual position is larger than the following error limit set under C Control lebze in positive direction.
Positive position limit C was exceeded. Best regards CS Moderator.
Troubleshooting and fault elimination, System error messages general error messages — Lenze 0. If you do not have the information, I strongly suggest you get purchase the Helmholts CAN parametrization software and the handling blocks for the S, so you can concentrate on your project making the drives do what you need them to do instead of finding ways to talk to the drives.
A parameter set with final speed must be followed by a parameter set with positioning; it is not permissible to wait for input.
vector inverters – Lenze in Lithuania. As easy as that.
Actual reference dimension offset C outside the position limits. If necessary, adapt the position limit values or check whether the program function “set position value” is to be applied.
During initialisation of the controller, an incorrect power stage was detected. Error in positioning program. Positive limit switch was reached. Hope this helps, Daniel Chartier. An absolute parameter set C was performed during relative positioning position mode C