508D MANUAL PDF

508D MANUAL PDF

I’ve found the installation manual (for my reference), but the D is giving me the most headaches at the moment. If someone can e-mail. Moblie phone manual details for FCC ID 2AL4OSSB made by SSB Trading Inc.. Document Includes User Manual manual. Manual or automatic transmission selection. Note: In the case of D, power and ground must be hardwired to the vehicle – power and.

Author: Faugal Moogunos
Country: Bhutan
Language: English (Spanish)
Genre: Marketing
Published (Last): 6 April 2007
Pages: 34
PDF File Size: 19.52 Mb
ePub File Size: 3.89 Mb
ISBN: 520-9-33932-821-5
Downloads: 78387
Price: Free* [*Free Regsitration Required]
Uploader: Dashakar

With a 10K resistor connected between the output and the 16V rail sorry, no 5V available right nowit reads 15V at the output when inactive, but drops to zero when triggered. Thanks for your help! I know thread is old.

Open-collector or open-drain, same thing outputs are nice and flexible like this you can wire several of them together to one pull-up resistor to make a hard-wired AND gate too.

Collision indicator It will flash when 10 Mbps segment network collision occurs. This means you can connect the signal pin to a Arduino digital input pin, but you need to connect it to a pull up resistor so you get a constant value. Don’t have an account? Great, thanks so much for your help! Please orient the cable correctly and push it into the connector until you hear a click. I took a few electronics courses back in college, but have forgotten most of it.

By pressing ‘print’ button you will print only current page.

When I first tried hooking this up to my Arduino I was worried about the sensor running on 12v. But I found good input to the initial problem under: Table of Contents Add to my manuals Add. Comments to this Manuals Your Name. If both generate an output then take note of the voltages involved.

  JULIO FRENK TRIPTOFANITO PDF

Check the PDF Manual: Product Limited Warranty Acer Netxus Incorporated ANI warrants its product to be free from defects in materials and workmanship, under normal use and service, for the following lengths of time from the date of purchase from ANI or its Authorized Resellers. Enter text from picture: This company makes no representations or warranties, either expressed. Acer 8-port dual-speed ethernet hub user’s manual alhds 32 pages.

d Install Manual For Aux

Without a resistor, it measures 0V when inactive, about 6. The blue wire is “alarm” – someone’s entered the smaller alarm perimeter. Further, this company reserves. I didn’t want to pass that voltage into the Arduino and fry it. That means it’s grounding, right?

DEI Viper 508d Manual and Advice?

Collision indicator It will flash when Mbps segment network collision occurs. MarkT Brattain Member Posts: Product Limited Warranty A. Quick Installation Guide 1. Table Of Contents Table of Contents 0. Measure the output voltages with nothing connected, and then again with 10k resistor from output to 5V. When the alarm is triggered the signal pin is connected to ground.

Page maual You can use the uplink port of the Ethernet hub to uplink to normal port of ALHd to upgrade some key network user from 10Mbps to Mbps by connect to ALHd and leave the others connect to the Ethernet hub segment. It’s a 12V circuit, it has two outputs which I’d like to sense. However I’d suggest it would be best to mankal.

  LINKSYS SPA2102-EU PDF

You can use the uplink port of the Ethernet hub to uplink to normal port of ALHd to upgrade some key network user from 10Mbps to Mbps by connect to ALHd and leave the others connect to the Ethernet hub segment. How would I sense that, and is it OK to connect that resistor directly to the Arduino’s 5V power even though this runs on car 12V?

Page of 13 Go. Acer dual-speed ethernet hub user’s guide alhds 32 pages.

Acer ALH-508d User Manual

Led Indicators And Ports Description 2. Is there something I can read online to get a better understanding?

I’m also trying to use this sensor, but confused about what the blue and green wires do. No part of this. Eventually I realized that the signal pins are left floating when the alarm is not triggered.

No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in manul form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of this company.

Got it, continue to print. To print the manual completely, please, download it.

Don’t show me this message again. If only the latter works and gives Table of Contents 0.

A Communications Company of Acer Now I’m starting to see what the term “pull-up resistor” actually means! This is the “manual”: